抗倍特板材作為高密度的人造板材，質地很堅硬。因此富美家抗倍特板廠家認為，在使用的抗倍特板時應注意以下幾個方面：

As a high density artificial board, the quality of the anti Beite board is very hard. Therefore, the manufacturer of Fumeijia MP special plate believes that the following aspects should be paid attention to when using MP special plate:

1.開料時，需要以直線鋸切為主。通?？上仍诳贡短匕宀纳袭嫼靡?guī)格尺寸，然后再鋸切。如果工件的尺寸為標準尺寸，可先用模板劃線后再進行鋸切，這樣會更加方便。

1. Straight sawing is the main method for cutting. In general, the specifications and dimensions can be drawn on the special resistance plate before sawing. If the size of the workpiece is the standard size, the template can be used for scribing before sawing, which will be more convenient.

2.開孔時，可以使用手提曲線鋸進行切割，切割速度控制在3-4m/min為宜。如果切割速度過快，一方面可能會造成切割邊緣爆口等缺陷，另一方面也可能會影響鋸條的使用壽命，增加加工的成本。

2. When opening holes, the portable curve saw can be used for cutting, and the cutting speed should be controlled at 3-4m/min. If the cutting speed is too fast, on the one hand, it may cause defects such as cutting edge bursting, on the other hand, it may also affect the service life of the saw blade and increase the processing cost.

3.對異形邊沿進行加工時，需要先在板件表面劃出所需尺寸，然后使用曲線鋸切割；如果是批量生產，可以在模板的輔助下進行切割，這樣可同時確保加工速度和鋸切質量。

3. When processing the irregular edge, it is necessary to draw the required size on the surface of the plate first, and then use a curve saw to cut; In case of batch production, cutting can be carried out with the aid of the template, which can ensure the processing speed and sawing quality at the same time.

4.加工邊緣，通常采用的工具是手提鏤銑機。加工之前需要清除板件表面的灰塵或異物，以免在板件表面留下劃痕或刻痕。另外鏤銑機的加工速度應保持在2m/min為宜。如果鏤銑刀刀刃角度較小而工件厚度又較厚時，鏤銑機的加工速度應適當放慢。

4. Handheld router is usually used to process edges. Before processing, it is necessary to remove the dust or foreign matters on the surface of the panel to avoid leaving scratches or nicks on the surface of the panel. In addition, the processing speed of the router should be kept at 2m/min. If the cutting edge angle of the router is small and the workpiece thickness is thick, the processing speed of the router should be appropriately slowed down.

5.砂磨時，按順序分別采用80＃、220＃和320＃砂紙對邊緣進行砂磨。打磨速度以2.5米/15-20分鐘為基準。打磨時，應注意不要損壞表面裝飾層。打磨結束后，用拋光劑對邊緣進行拋光處理。

5. During sanding, the edges shall be sanded with 80 ＃, 220 ＃ and 320 ＃ sandpaper in sequence. The grinding speed is based on 2.5m/15-20min. When grinding, be careful not to damage the surface decorative layer. After polishing, polish the edges with polishing agent.

6.拼接板件時，應注意粘合劑的涂布量需要控制在2.5-3.0g/cm2，并且要確保涂布到全部粘接表面；拼接后，用夾子壓合30分鐘左右。豎直方向粘合時，一定要開口，增大粘合面，以確保粘合的強度；一旦發現被粘合部件有爆口等缺陷，需要將光滑平整的一面朝外，以保證粘合的質量。

6. When splicing plates, it should be noted that the amount of adhesive coating should be controlled within 2.5-3.0g/cm2, and it should be ensured that all bonding surfaces are coated; After splicing, press with clips for about 30 minutes. When bonding in the vertical direction, be sure to open and increase the bonding surface to ensure the bonding strength; Once it is found that the bonded parts have defects such as bursting, the smooth and flat side needs to be outward to ensure the quality of bonding.

7.如果是利用螺釘連接產品的，需要先用比螺釘直徑小的鉆頭鉆一個小孔，然后向小孔注入粘合劑。后把螺釘擰入，并確保螺釘牙紋的上沿部分擰入5mm以上。

7. If the product is connected by screws, it is necessary to drill a small hole with a drill bit smaller than the screw diameter, and then inject adhesive into the hole. Then screw in the screw and ensure that the upper edge of the screw thread is screwed in more than 5mm.

8.在鉆杯狀暗鉸鏈孔時，板件的剩余厚度應該保留在3mm以上。如剩余厚度過薄，杯狀鉸鏈埋入后，會產生破損或出現凸痕。裝暗鉸鏈時，孔底和固定螺絲孔內應涂上粘合劑，然后再用螺釘擰緊。緊固螺釘時，不要過度，否則也會使板件邊緣部分外凸，嚴重時會將其頂破。

8. When drilling cup shaped concealed hinge holes, the remaining thickness of the plate should be kept above 3mm. If the remaining thickness is too thin, the cup-shaped hinge will be damaged or have bumps after being embedded. When installing the concealed hinge, the bottom of the hole and the inside of the fixing screw hole should be coated with adhesive, and then tightened with screws. Do not tighten the screws too much, otherwise the edge of the panel will bulge, and it will burst in severe cases.

抗倍特板在安裝結束時，如果表面出現斑點或污跡，可用毛巾沾取少量油性清潔劑(油與丙酮的混合物)輕輕擦拭去這些斑點或污點。如果沒有斑點或污跡，用一般清潔劑如肥皂加水，或洗潔精加水擦拭即可。更多相關事項就來我們網站http://www.qq1980.cn咨詢吧！

At the end of the installation of the anti magnification special plate, if there are spots or stains on the surface, use a small amount of oily cleaner (mixture of oil and acetone) dipped in a towel to gently wipe away these spots or stains. If there is no spot or stain, wipe it with general detergent such as soap and water, or detergent and water. Come to our website for more information http://www.qq1980.cn Consult!