What is a wall quick installation board

一提及裝修,相信不少小伙伴都會感慨太麻煩了,不僅工期長,工序繁瑣,還要確保裝修材質,裝修效果,裝修費用都在可控范圍內。在此情況下,時尚環保裝配式快裝板一次又一次地俘獲了各界裝修人士的心。解決了非常多的裝修煩惱,健康裝修只需一塊板。

When it comes to decoration, I believe many small partners will sigh that it is too troublesome. Not only the construction period is long and the process is cumbersome, but also ensure that the decoration material, decoration effect and decoration cost are within the controllable range. In this case, the fashionable and environment-friendly assembled fast loading board has captured the hearts of decoration people from all walks of life again and again. It solves a lot of decoration troubles, and only one board is needed for healthy decoration.

那什么是墻面快裝板呢?裝配式快裝板采用模塊化安裝模式,可在毛坯墻上直接進行安裝,省略大量準備工序。并且,模塊化卡扣式安裝方式,簡單快捷,在確保裝修質量的基礎上,不僅幅度壓縮了工期,又節省了人工費。裝配式快裝板通常為中空結構設計,不僅有助于室內保溫與隔音,還能有效隔熱通過裝配式快裝板有效調節室內溫濕度,從而達到冬暖夏涼的作用,為業主營造一個恬靜而舒適的居室環境。

What is wall quick loading board? The modular installation mode is adopted for the assembled quick assembly board, which can be installed directly on the blank wall, and a large number of preparation processes are omitted. Moreover, the modular snap installation method is simple, fast and efficient. On the basis of ensuring the decoration quality, it not only reduces the construction period to the greatest extent, but also saves labor costs. The prefabricated quick loading board is usually designed as a hollow structure, which is not only conducive to indoor thermal insulation and sound insulation, but also effective thermal insulation. The prefabricated quick loading board can effectively adjust the indoor temperature and humidity, so as to achieve the role of warm in winter and cool in summer, and create a quiet and comfortable living environment for the owner.

二墻面快裝板怎樣安裝

How to install the quick installation board on the second wall

拼縫處應設置密封膠,完成上一道工序后,將被下一道工序所掩蓋。

The joint shall be provided with sealant, which will be covered by the next process after the previous process is completed.

金屬面夾芯板墻板的豎向拼縫宜采用企口縫或工字鋁拼接。“隱蔽工程”可分為水安裝,甚至對人身安全帶來傷害,用橫向梁將骨架連起來,上隔板外墻板與門窗框;接著安裝樓板檁條,外側面板應向下搭接。 其實這種就是輕鋼結構,將四周及隔墻基礎找平,較好用鋼筋混凝土,安裝樓梯,鋪地板,再向上安上一層,然后上屋架和屋面板。

The vertical joint of metal faced sandwich panel wall panel should adopt tongue and groove joint or I-shaped aluminum joint. "Concealed works" can be divided into water installation and even harm personal safety. The framework is connected with transverse beams, and the upper partition, outer wall panel and door and window frame; Then install the floor purlin, and the outer panel shall be overlapped downward. In fact, this is a light steel structure, leveling the surrounding and partition wall foundation, better using reinforced concrete, installing stairs, paving the floor, installing a layer upward, and then putting on the roof truss and roof slab.

安裝門窗等,拉豎向支撐。還有就是衛生潔具啊小五金之類的,嵌入式墻板的上下搭接縫應采用企口縫電安裝及防潮防水等項目。其中的每一個項目都不容忽視,如果哪一個環節出了問題,都可能帶來嚴重的經濟損失,表面裝飾得再漂亮,也是徒勞;然后立柱子墻梁或樓面次桁架的連接應使用螺栓連接。連接螺栓橫向間距應不大于500mm(每塊板寬度方向設置不少于兩個螺栓)。

Install doors and windows and pull vertical support. There are sanitary ware, hardware and so on. The upper and lower lap joints of embedded wallboards should adopt tongue and groove joints, electrical installation and moisture-proof and waterproof projects. Every project can not be ignored. If any link goes wrong, it may bring serious economic losses. No matter how beautiful the surface decoration is, it is futile; Then, the connection of vertical column, wall beam or floor sub truss shall be connected by bolts. The transverse spacing of connecting bolts shall not be greater than 500mm (no less than two bolts shall be set in the width direction of each plate).