現在家庭裝修，不少人喜歡選擇防火板裝飾板，那么防火板裝飾板施工要注意的問題有哪些，也是人們關心的重點，人們要求的防火板裝飾板既美觀又要實用，這些問題不斷的被提出，現在，就讓我們一起了解一下吧。

Now, many people like to choose fire-resistant decorative board for home decoration. What problems should be paid attention to in the construction of fire-resistant decorative board are also the key points that people care about. The fire-resistant decorative board that people require is both beautiful and practical. These problems have been constantly raised. Now, let's get to know it together.

1、找位與彈線：防火板裝飾板安裝前應根據設計圖集要求，事先找好標高，平面位置、豎向尺寸進行彈線。核查預埋件及洞口：彈線后檢查預埋件，木磚或木楔是否符合設計要求，排列間距尺寸、位置是否滿足釘裝龍骨的要求；量測門窗及洞口位置尺寸是否方正垂直且與設計要求是否相符。

1. Locating and snapping lines: Before the installation of fireproof board decorative plate, the elevation, plane position and vertical dimension shall be determined in advance according to the requirements of the design drawings. Check the embedded parts and holes: after snapping the line, check whether the embedded parts, wood bricks or wooden wedges meet the design requirements, and whether the arrangement spacing size and position meet the requirements for nailing keel; Measure whether the position and size of doors, windows and openings are square and vertical and conform to the design requirements.

2、鋪、涂防潮層：設計有防潮要求時木護墻、木龍骨安裝須找方、找直，骨架與木磚間的空隙應墊木墊，每塊木磚至少用2個釘子釘牢，再裝釘龍骨時應預留出板面厚度。木龍骨與墻體接觸面要進行防腐處理，其余三面進行不少于三遍的防火涂料的處理。

2. Paving and painting damp proof course: when the design requires damp proof, the installation of wooden parapet wall and wooden keel must be square and straight. The gap between the skeleton and the wooden bricks should be padded with wood pads. Each wooden brick should be nailed with at least 2 nails. The thickness of the board should be reserved when the keel is installed. The contact surface between the wooden keel and the wall shall be treated with anti-corrosion, and the other three surfaces shall be treated with at least three times of fireproof coating.

3、安裝面板：面板選色陪紋：面板進場使用前，按同房間、臨近部位的用量進行挑選，是安裝后從觀感上木紋、顏色一致。裁板配制：按龍骨排尺，大于龍骨間距進行裁板，據裁后大面應凈光（膠合板材嚴禁側凈），小面刮直。面板長向?qū)优渲茣r須考慮接頭位于橫撐處，板背面應做卸力槽，以防板扭曲變形，一般卸力槽間距為100mm，槽寬10mm，槽深6－8mm。

3. Installation panel: color matching of panel: before the panel is put into use, it shall be selected according to the amount of the same room and adjacent parts, so that the wood grain and color are consistent from the appearance after installation. Cutting preparation: cut the board according to the keel arrangement, which is greater than the keel spacing. After cutting, the large surface should be clean (plywood should not be clean on the side), and the small surface should be straight. When preparing the longitudinal butt joint of the panel, it must be considered that the joint is located at the cross brace, and the back of the panel should be provided with a relief slot to prevent the panel from twisting and deformation. Generally, the spacing of the relief slot is 100mm, the slot width is 10mm, and the slot depth is 6-8mm.

4、面板安裝：面板安裝前對龍骨位置、平直度、釘設牢固情況、防潮層等構造要求進行檢查，合格后進行安裝；面板配好后進行試裝，面板尺寸、接縫、接頭處構造完全合適，木紋方向、顏色觀感尚可的情況下，才能正式進行安裝；

4. Panel installation: before panel installation, check the keel position, straightness, firmness of nails, moisture-proof course and other structural requirements, and install after passing the inspection; Trial assembly shall be carried out after the panel is assembled. Formal installation can only be carried out when the panel size, joint and joint structure are completely appropriate and the wood grain direction and color appearance are acceptable;

面板接頭處安裝時應涂膠與龍骨釘牢，釘固面板的釘子規格應適宜，釘子長度約為面板厚度的2－2．5倍，釘子間距一般為100mm，釘帽應砸扁，并用沖子將釘帽順木紋方向沖入面板1－2mm；釘貼臉：貼臉料應進行挑選、花紋、顏色應與框料、面板近似。貼臉的規格尺寸、厚度應一致，接茬應順平無錯槎。

When installing the panel joint, it should be coated with glue and nailed firmly to the keel. The specification of the nails used to nail the panel should be appropriate. The length of the nails should be about 2-2.5 times the thickness of the panel. The spacing between nails is generally 100mm. The nail cap should be flattened and punched into the panel 1-2mm along the direction of the wood grain; Nail facing: The facing materials shall be selected, and the patterns and colors shall be similar to those of the frame materials and panels. The specification, size and thickness of the veneer shall be consistent, and the joints shall be smooth without any wrong joint.

所以這就是為什么我們說，防火板裝飾板施工建議按照一定操作規范使用，只有這樣，才會讓問題盡量避免不出現。您對此還有什么問題，就來我們網站http://www.qq1980.cn進行了解吧！

So this is why we say that it is recommended to use the fireproof board decorative board according to certain operating specifications. Only in this way can problems be avoided as far as possible. If you have any questions about this, please come to our website http://www.qq1980.cn Get to know!