1、切割材料時應以直線鋸切為主。通常，您可以先在板上畫出規格和尺寸，然后再看到。如果工件尺寸是標準尺寸，可以在鋸前用模板劃線，方便很多。

1. Linear sawing shall be the main method for cutting materials. Usually, you can draw the specifications and dimensions on the board before you see them. If the workpiece size is a standard size, you can use a template to draw lines before sawing, which is much more convenient.

2、開孔時，可用便攜式曲線鋸切割。切割速度為3-4m/min。如果切割速度過快，一方面會使刃口出現爆裂等缺陷，另一方面也會影響鋸片的使用。壽命，增加不必要的加工成本。

2. Portable curve saw can be used to cut holes. The cutting speed is 3-4m/min. If the cutting speed is too fast, on the one hand, the cutting edge will burst and other defects, on the other hand, it will also affect the use of the saw blade. Life, increase unnecessary processing costs.

3、富美家A級墻板加工時，應先在板面畫出所需尺寸，再用曲線鋸切割；如果大批量生產，可以使用大型CNC進行切割，這樣可以保證加工速度和鋸切質量。

3. During the processing of Formica class a wall panels, the required dimensions shall be drawn on the panel surface first, and then cut with a curve saw; In case of mass production, large CNC can be used for cutting, which can ensure the processing speed and sawing quality.

4、邊緣加工操作前應清板面的灰塵或異物，以免在板面留下劃痕或劃痕。路由器的加工速度應保持在2m/min。如果銑刀的刃角小，工件的厚度較厚，則應適當放慢銑刀的加工速度。

4. Before edge processing, the dust or foreign matters on the plate surface shall be removed to avoid scratches or scratches on the plate surface. The processing speed of the router shall be kept at 2m/min. If the edge angle of the milling cutter is small and the thickness of the workpiece is thick, the processing speed of the milling cutter should be appropriately slowed down.

另外，銑刀刃口的長度應大于工件的厚度，以保證一次走刀就能銑出刃口的線形。通過時，刳刨機應從高位逐漸下滑至較低位置，直至刳刨機刃蓋住銑刃。值得注意的是，刀一定要保持穩定，不要讓路由器晃動?；蝿訒构ぜ吘壆a(chǎn)生不規則的波紋，增加后續打磨拋光工序的工作量，影響加工效率。

In addition, the length of the cutting edge of the milling cutter shall be greater than the thickness of the workpiece to ensure that the linear shape of the cutting edge can be milled out at one time. When passing, the planer shall gradually slide down from the high position to the low position until the planer edge covers the milling edge. It is worth noting that the knife must remain stable and do not let the router shake. Shaking will cause irregular ripples at the edge of the workpiece, increase the workload of the subsequent grinding and polishing process, and affect the processing efficiency.

5、打磨時，用80#、220#、320#砂紙依次打磨邊緣。打磨速度以15-20分鐘2.5米長度為準；打磨時應注意不要損壞表面裝飾層。用拋光劑拋光邊緣。拋光劑可以使用人造大理石的拋光蠟，拋光程序如下：

5. When polishing, polish the edges with 80\220\320\. The grinding speed shall be subject to the length of 2.5m within 15-20 minutes; Be careful not to damage the surface decorative layer during grinding. Polish the edges with polish. The polishing agent can use the polishing wax of artificial marble, and the polishing procedure is as follows:

用柔軟的棉布蘸取適量的拋光蠟，擦拭邊緣；

Dip a proper amount of polishing wax with a soft cotton cloth and wipe the edge;

拋光蠟干后，在邊緣涂上一層拋光蠟，用布擦拭，使其有光澤，后涂上一層拋光蠟，用干凈的布擦拭，直到邊緣光亮。

After the polishing wax is dry, apply a layer of polishing wax on the edge and wipe it with a cloth to make it shiny. Then apply a layer of polishing wax and wipe it with a clean cloth until the edge is bright.

6、富美家A級墻板拼板時應掌握以下幾點：

6. The following points shall be mastered when Formica class a wallboard is assembled:

膠粘劑的涂布量應控制在2.5-3.0g/cm2，粘合面應充分涂布；

The coating amount of adhesive shall be controlled within 2.5-3.0g/cm2, and the bonding surface shall be fully coated;

拼接后，用夾子夾住約30分鐘。垂直方向粘接時，必須打開開口，增加粘接面，保證粘接強度；

After splicing, clamp for about 30 minutes. When bonding vertically, the opening must be opened to increase the bonding surface to ensure the bonding strength;

一旦發現待粘接的零件有裂紋等缺陷，應將光滑平整的一面朝外，以保證粘接質量。

Once cracks and other defects are found on the parts to be bonded, the smooth and flat side shall face outward to ensure the bonding quality.

7、如果要使用螺釘連接產品，應先用比螺釘直徑小的鉆頭鉆一個小孔，然后在小孔內注入粘合劑，然后擰入螺釘，并確保螺紋上緣旋入5mm以上。

7. If screws are used to connect products, drill a small hole with a drill bit smaller than the screw diameter, then inject adhesive into the small hole, then screw in the screws, and ensure that the upper edge of the thread is screwed in more than 5mm.

8、鉆杯形隱鏈孔時，板的剩余厚度應保持至少3mm。如果剩余厚度太薄，嵌入后會損壞杯形鉸鏈或出現凸痕。安裝暗鏈時，孔底和固定螺絲孔要涂上粘合劑，然后用螺絲擰緊。螺釘不要擰得過緊，否則板邊會突出，嚴重時會折斷。

8. When the cup-shaped hidden chain hole is drilled, the remaining thickness of the plate shall be kept at least 3mm. If the remaining thickness is too thin, the cup hinge will be damaged or convex marks will appear after insertion. When installing the concealed chain, the bottom of the hole and the fixing screw hole shall be coated with adhesive, and then tightened with screws. Do not over tighten the screws, otherwise the plate edge will protrude and break in serious cases.

9、如果安裝結束時富美家A級墻板表面有斑點或污漬，可以用毛巾沾上少量油性清潔劑（油和丙酮的混合物）輕輕擦拭這些斑點或去除污漬。如果沒有斑點或污跡，請使用肥皂和水等一般清潔劑或清潔劑和水擦拭。

9. If there are spots or stains on the surface of Formica class a wallboard at the end of installation, gently wipe these spots or stains with a towel dipped with a small amount of oily detergent (a mixture of oil and acetone). If there are no spots or stains, wipe with general detergent such as soap and water or detergent and water.

以上就是今天為大家分享的關于問題的相關內容，希望對大家能有所幫助，想要了解更多內容可以電話聯系我們或者關注我們的網站http://www.qq1980.cn。

The above is the relevant content about the problem shared for you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website http://www.qq1980.cn 。