廠家生產防火板時時常會遇到什么問題_公司新聞_新聞動態-山東創圖建筑裝飾工程有限公司

廠家生產防火板時時常會遇到什么問題

來源：http://www.qq1980.cn/ 日期：2022-11-25 發布人：admin

富美家防火板表面裝飾用耐火建材，有豐富的表現色彩、紋路、以及特殊的物理性能。在室內裝飾、公共裝飾等領域都有廣泛的應用。廠家生產防火板時時常會遇到什么問題？

Fumeijia fireproof board is a fire-resistant building material for surface decoration, which has rich expressive colors, lines and special physical properties. It is widely used in interior decoration, public decoration and other fields. What problems do manufacturers often encounter when producing fireproof boards?

1.板材開裂：

1. Plate cracking:

（1）樹脂反應過嫩，分子太??；（2）樹脂固化不全；（3）表層的塑膜紙含膠量太高

(1) The resin is too tender and the molecule is too small; (2) Incomplete resin curing; (3) The plastic film paper on the surface has too high glue content

解決辦法：（1）停止使用不合適的樹脂；（2）適當?shù)奶岣邿釅簻囟然蛘哐娱L熱壓時間；（3）嚴格控制表層膠膜紙的的含膠量

Solution: (1) Stop using inappropriate resin; (2) Properly increase the hot pressing temperature or extend the hot pressing time; (3) Strictly control the glue content of the surface adhesive film paper
富美家防火板

2.防火板分層：

2. Lamination of fireproof board:

（1）膠膜紙揮發物含量太低，膠膜紙在干燥是局部樹脂固化；（2）膠膜紙樹脂含量不夠；（3）壓力過低或者熱壓時間不夠；（4）膠膜紙之間有雜物

(1) The volatile content of the adhesive film paper is too low, and the adhesive film paper is partially cured by resin during drying; (2) The resin content of adhesive film paper is insufficient; (3) Too low pressure or insufficient hot pressing time; (4) There are sundries between the adhesive film paper

解決方法：（1）控制揮發物含量不要過低，干燥溫度不要過高，時間不要過程、防止樹脂局部固化；（2）提升膠膜紙含量；（3）適當?shù)奶岣邏毫蜓娱L加熱時間；（4）鋪膜時注意清除雜物

Solution: (1) Control the volatile content not to be too low, the drying temperature not to be too high, the time not to process, and prevent local curing of the resin; (2) Improve the content of adhesive film paper; (3) Increase the pressure or extend the heating time appropriately; (4) Pay attention to removing sundries during film laying

3.防火板彎翹：

3. Fireproof plate warping:

（1）各種原紙組織成分厚薄不均勻；（2）膠膜紙含膠量不均勻，各處壓力不一致；（3）壓制過程中高溫后未能進行充分冷卻

(1) The thickness of various base paper organizational components is uneven; (2) The glue content of adhesive film paper is uneven, and the pressure is inconsistent everywhere; (3) Insufficient cooling after high temperature during pressing

解決的方法：（1）各種原紙應符合工藝要求；（2）保持樹脂濃度均勻，調整擠壓軸的間隙；（3）冷卻到50°以下在進行卸壓

Solutions: (1) All kinds of base papers should meet the process requirements; (2) Keep the resin concentration uniform, and adjust the gap of the extrusion shaft; (3) Cool to below 50 ° before pressure relief

以上就是廠家在板材生產過程中重容易遇到的一些問題，那我們作為用戶來講，如果遇到這些問題也不要慌張，聯系廠家http://www.qq1980.cn，找尋幫助。

The above are some problems that manufacturers are likely to encounter in the process of sheet production. As users, don't panic if you encounter these problems. Contact the manufacturer http://www.qq1980.cn , looking for help.

上一篇：抗倍特板的應用與維護 下一篇：生產潔凈板使用的原材料

分類導航

五月激情丁香,亚洲国产精品国自产拍久久,波多野,精品一区二区三区

產品中心

聯系我們

成功案例

聯系我們

新聞動態

聯系我們

熱門產品推薦

相關新聞